7/3/2009 · Kategori: teknoloji
VSEP Membrane Cleaners In addition to filtration systems, New Logic manufactures a complete line of chemical cleaners designed to maintain maximum flow rates in all VSEP applications.Years of exhaustive research and development by New Logic engineers have resulted in seven chemical cleaners formulated to attack the most stubborn foulants across a wide range of membranes and feed streams.While designed for VSEP membrane filtration systems, these advanced formulas are perfect for cleaning any membrane.To learn more about VSEP Advanced Cleaning Solutions, please choose a link below to visit our sister site http://www.membranecleaner.com/.
While membrane-based separations of liquids from solids have enjoyed increasing popularity over the last 20 years, the technology has an inherent Achilles heel that affects all membrane devices: fouling. This long-term loss in throughput capacity is due primarily to the formation of a boundary layer that builds up naturally on the membranes surface during the filtration process.In addition to cutting down on the flux performance of the membrane, this boundary or gel layer acts as a secondary membrane reducing the native design selectivity of the membrane in use.
Kalıcı Bağlantı
Yorum (yok)
Yorum yaz!
2/3/2009 · Kategori: teknoloji
ZTEC Instruments believes that modular instruments should provide users the same advanced acquisition and measurement feature sets that benchtop instruments have. That’s why our PXI, PCI, VXI, and LAN oscilloscopes and function generators stand out in the world of modular instruments. For example our M-Class oscilloscopes offer:
Advanced acquisition modes: averaging, envelope, peak detect, high resolution, and equivalent time
On-board waveform measurements and waveform math:
Automatically calculate 36 parameters related to waveform behavior
In addition to basic +, -, *, M-Class scopes can calculate FFT, derivative, integration, histogram, limit testing and mask testing waveforms
Advanced triggering: including rising/falling edge, pattern, state, pulse width, video, and multi-event cascading triggers
Segmented memory: Up to 32,000 waveforms can be viewed (overlaid or individually), saved and analyzed
Intuitive interface: Free ZScope software provides an intuitive graphical interface for controlling ZTEC’s modular oscilloscopes – control it just like a benchtop oscilloscope
Kalıcı Bağlantı
Yorum (yok)
Yorum yaz!
22/2/2009 · Kategori: teknoloji
30 years of experience and 6 generations of instruments (M210, M211, UF 320P, UF 321T, and now DigiSonic and Minisonic) permit us to offer the best of the technology and moreover the most pertinent information linked to your measurements works.
| |
To justify a measurement means being able to criticize it even on a pipe with one inaccessible pipewall.
To this end, our instruments are composed of (in accordance with our specification sheet)
| | - an internal or external thickness measurement
- a dynamic analyser of the " echo " signals, indeed a numeric oscilloscope function (Digisonic) because every pipe can disclose surprises
- an optimization function of time measurement, metrological advantage in comparison to correlation or phase difference measurement
- an access to physical measurements, like the " delta T ", the speed of sound, the signal level and their quality indexes.
|
The carrying out of a measurement must be as simple with : | | - a choice of adapted and high performance probes, including their supports
- simple and complete intuitive menus in your own language
- a readable, numeric and graphic display
- simple possibilities of data logging and export to the PC and printing possibilities.
- an important battery life and a fast charge of the battery
- a robustness for field survey work
|
Our applications have few limits and constantly improve themselves, accepting from ultrapure liquids to the one relatively charged or viscous and of pipes from 8mm to 5000mm.
As an example :
- The metrological checking of existing meters and flowmeters according to the accuracy required. Our instruments can meet all ISO 9000 requirements, therefore being checked and certified
- The supervision of indusrial, chemical and petrochemical process…no matter the aggression or pressure of the fluid. For the measurement in Ex area (hazardous), thank you for consulting us.
- The balancing of heating or air-conditioning network, with the possibility of calculating the calorific power with the " temperature measurement " option
- The measurement on hydraulic circuit with, associated to pressure measurement, the capacity to measure a power energy
- The analysis of dense network in drinking water distribution
- The detection of leaks in networks (Vivendi)
- The flow supervision in situ of pipes before and after repairing (Salmson pumps, Sulzer)
- The measurements with a risk of radioactive contamination (Cogema, SGN...) |
Kalıcı Bağlantı
Yorum (yok)
Yorum yaz!
14/1/2009 · Kategori: teknoloji
LONDON, England (CNN) -- A new robotic suit could transform the lives of paralyzed people, giving them the ability to walk again.
The invention, known as ReWalk, acts like a kind of exoskeleton. It consists of lightweight, motorized leg supports and an assortment of intricate motion sensors.
Users wear a backpack that holds a computerized control box which helps the medical device recognize when a step needs to be taken.
"Standing changes my whole environment. I don't have to look from the bottom up. Now I am eye to eye with everybody," Radi Kaiof, who has used the device, told CNN.
Kaiof, a former Israeli soldier, was paralyzed from the waist down 20 years ago. He doesn't have feeling in his legs but is still able to move with the use of the robotic suit
With the assistance of crutches, which offer balance and support, people paralyzed from the waist down can walk, bend, sit and even climb stairs when they wear the suit.
The futuristic invention offers an alternative to using a wheelchair for those who have functioning upper bodies and are capable of standing with the use of supports.
It is the creation of Dr. Amit Goffer, an engineer and founder of Haifa, Israel-based high-tech firm Argo Medical Technologies. Goffer was inspired to create the device more than a decade ago after he became disabled in an accident.
The medical technology that could help paraplegics do what was once considered impossible isn't available for purchase yet. The device wasn't ready for testing until late 2007 and currently is in clinical trials in Tel Aviv. 
More trials are planned for the United States and Europe, and if the product receives the necessary approvals, it could hit the market in 2010.
The price of the device hasn't been set yet, but is expected to be comparable with the typical average yearly expense of using a wheelchair.
The robotic suit improves the quality of life of people paralyzed from the waist down, according to Goffer, who wanted to give paraplegics an alternative to using a wheelchair. It also benefits their overall health since it keeps their bodies active all day long, he says.
But when it comes down to it, the invention is all about helping people regain respect. Dignity is "the No. 1 problem" for people who use wheelchairs, says Goffer.
For Kaiof, the former soldier, the robotic suit has changed his life. Before he tried it on, his daughter had never seen him stand before.
When he stood before her for the first time, she couldn't believe just how tall he was, he recounted to CNN.
Kalıcı Bağlantı
Yorum (yok)
Yorum yaz!
2/1/2009 · Kategori: teknoloji
Ideal for the measurement of flow, density and temperature of liquids and slurries, such as aggressive or contaminated, sanitary or particle-filled fluids.
Features: - Flow ranges from 60 to
60K Kg/Hr (2.2 to 1650 lb/min) - Accuracy up to 0.25% of reading
- Materials: flow tubes -
316 L, splitter flanges -
316 Ti, housing - cast iron - Process temperature
-40°F to 356°F - Ambient temperature
-40°F to 140°F - Wide flow ranges
ACCURATE AND RELIABLE
This meter has the ability to
maintain high accuracy,
despite changing viscosity conditions, with accuracy of +0.25% of reading.
EASY CLEANING
The ACM series has smooth stainless steel tubes and no moving parts, and is therefore very easy to flush and clean.
MULTI-TASKING
The ACM series of mass coriolis flow meters measure flow, density and temperature.
MATERIAL COMPATIBILITY
Because of the meter's 316 stainless steel flow tubes, the ACM series can measure a wide range of materials.
VARIETY OF ELECTRONICS
Electronics available for the ACM series include a local, hazardous rated display and a remote, panel-mount digital display.
Kalıcı Bağlantı
Yorum (yok)
Yorum yaz!
1/1/2009 · Kategori: teknoloji
Do you want an installed method of regularly assessing the operation of your distillation tower, reducing operating costs and reducing shutdown time?
To meet the changing needs of our customers the Tracerco research and development team has designed an alternative technique to conventional tower scanning. The TRACERCO Diagnostics™ RapidScan technology combines sophisticated wireless detector capability with an easy to install permanent scanning guide wire system.
The TRACERCO Diagnostics™ Tower Scan method has been used for over 20 years by many major chemical and refining companies around the world. The combined data acquisition software from these techniques coupled with TRACERCO Diagnostics™ RapidScan hardware increases efficiency and reliability of scan data by providing fast, consistent data acquisition from fixed orientations. The service allows repeatable tower scanning that can quickly evaluate mechanical or process 
related problems offering plant personnel a cost effective process diagnostics solution to optimize or troubleshoot tower performance. Even columns with limited or zero ladder access do not pose an obstacle following installation of a TRACERCO Diagnostics™ RapidScan system.
- Improved Accuracy - the scans will use a fixed orientation so repeat scans are guaranteed to utilise identical geometries
- Better Data Reliability – data will not be affected by weather conditions (wind)
- Increased Safety – all scanning operations will be from ground level with no need to climb the tower, eliminating workingfrom heights
- Greater Cost Savings – after initial setup, the high costs of scaffolding or cranes for columns that have inadequate or no access is eliminated
- Enhanced Efficiency – reduces time needed to conduct a scan lessening the burden on operations to hold column at set conditions
The capabilities of conventional tower scanning are not lost. In fact, the TRACERCO Diagnostics™ RapidScan system potentially improves our ability to diagnose more subtle process changes by stringently controlling and eliminating variability in scan line orientations and paths.
Features Identified
- Tray damage
- Liquid maldistribution/blockages in packed beds
- Tray liquid loading
- Jet and liquid stack flooding
- Packing damage
- Distributor performance
- Presence and density of foam
All of the stainless steel pulleys and bracket work will be attached to the existing structure using insulation bands utilising the ‘band-it’ system. No welding or direct attachment to the column walls is required; hence the vessel pressure envelope will not be affected.
Kalıcı Bağlantı
Yorum (yok)
Yorum yaz!
29/12/2008 · Kategori: teknoloji
AkPCE-OM 100A / PCE-OM 200ku - Stroboskop
Tragbares, akkubetriebenes Stroboskop für den Profi im Betrieb /
lieferbar in zwei Varianten mit unterschiedlichen Messbereichen und Genauigkeiten
Das Stroboskop wird meist eingesetzt zur Drehzahl- bzw. Schwingungsmessung oder auch für Bewegungsbeobachtungen. Dieses Stroboskop besitzt eine kleine Bauform und hat ein geringes Gewicht. So kann das Stroboskop selbst bei Messungen an schwer zugänglichen Stellen bequem eingesetzt werden. Das Gerät ist das optimale Werkzeug für den Praktiker.
Die Blitzfrequenz wird über einen Drehknopf am Stroboskop eingestellt und auf einem digitalen Display angezeigt. Ein Dauerbetrieb ist mit dem Stroboskop problemlos möglich. Das Gerät verfügt zusätzlich über einen Triggereingang, wodurch eine externe Triggerung bzw. Synchronisation ermöglicht werden. Die Versorgungsspannung wird von einem internen wiederaufladbaren Akku geliefert. So ist das Stroboskop völlig flexibel einsetzbar. Die Erfahrung zeigt, dass der Akku über viele Jahre hinweg hält. Über Tastatur kann die halbe oder doppelte Drehzahl angewählt werden. Unsere weiteren Stroboskope sehen Sie auf der Stroboskope-Oberseite. Beispiele für die Verwendung des Gerätes sehen Sie hier.
Akku-betriebenes Stroboskop PCE-OM 100A
in Standardausführung
Bedienungsanleitung von diesem Stroboskop
ansehen / ausdrucken:
Akku-betriebenes Stroboskop PCE-OM 200
mit erhöhter Genauigkeit
Bedienungsanleitung von diesem Stroboskop
ansehen / ausdrucken:
Triggereingang / Display
Durch den externen Triggereingang kann das Stroboskop getriggert werden. Der Anschluss geschieht über einen 2-poligen NPN. Der Eingang ist TTL-kompatibel. Am Stroboskop ist der Drehknopf zur Frequenzeinstellung während einer Triggerung deaktiviert, solange der Triggerstecker eingesteckt ist. Das Triggerkabel selbst, ein normales TTL-Kabel bieten wir nicht an. Dieses Kabel ist sehr einfach in jedem Musikgeschäft oder Hifi-Geschäft zu bekommen. Die nachfolgenden Bilder geben Ihnen einen Eindruck über die Bedieneinheit, das Display und die Trigger-Stecker auf der Stroboskop-Rückseite.
Leuchtkegel
Einsatzgebiete
Dieses Stroboskop ist das ideale Werkzeug für Service-Techniker und Instandhaltungspersonal von industriellen Anlagen und Maschinen. Überprüfen Sie die Drehzahl, den Gleichlauf oder machen Sie Fehler sichtbar, die Sie mit bloßem Auge gar nicht erkennen - bringen Sie Prozesse optisch zum Stillstand.
Das Stroboskop hat sich seit Jahren in vielen industriellen Prozessen, aber auch in der Forschung u. Entwicklung bewährt:
- an Abfüllanlagen und Etikettiermaschinen von Brauereien und Mineralwasserproduzenten
- an Papier- und Druckmaschinen
(Druckerei: Das Stroboskop dient hier dem Erkennen des Passers bei Geschwindigkeiten über 60
m/min. Man betrachtet die Bahn vor der Aufwicklung mit dem Stroboskop).
Mit dem Stroboskop kann man sehr gut kleinste Prozessfehler, wie z.B. Pulsationen optisch
sichtbar machen. Das nachfolgende Bild wurde an dem Langsieb einer Papiermaschine gemacht.
Alle Leisten und Sauger unterhalb des entlang dieser Leisten laufenden Siebes arbeiteten ein-
wandfrei, bis auf eine. Dies war natürlich optisch nicht sichtbar. Mit dem Stroboskop konnte die
Fehlerquelle von sehr feinen Markierungen am fertigen Papier erkannt werden.
- an Webmaschinen in Textilfabriken
- in der Automobilindustrie
- an schnelllaufenden Maschinen und Motoren
Das Stroboskop wird wesentlich zur Ermittlung der Drehzahl, wie auf dem nebenstehenden Bild zu sehen ist, verwendet. Oftmals dient dies der Überprüfung bzw. dem Abgleich der Drehzahl von grossen Schnellläufern mit den Daten aus dem Prozessleitsystem oder dem an einer Digitalanzeige angegebenen Drehzahlwert, der meist elektrisch vom Antrieb her kommt.
Zudem wird der Wellenschaft auf Rundlauf geprüft. Somit ist das Stroboskop das optimale Werkzeug zur Inspektion von Motoren, Wellen, Treibriemen, Zylindern... eben vom allem, was rotiert, im Betrieb.
- an Ventilationssystemen in der Klimaindustrie
- an Bandwalzanlagen in der Stahlindustrie
- ... überall dort, wo drehende Teile im Einsatz sind oder in Produktionsprozessen mit hohen Stückzahlen ist das Stroboskop das optimale Hilfsmittel
Hinweis zur Unfallverhütung beim Einsatz vom Stroboskop: Alle Objekte, die mit dem Stroboskop optisch zum Stillstand gebracht werden, bewegen sich mit hoher Geschwindigkeit. Bewahren Sie deshalb immer einen Sicherheitsabstand und berühren Sie nicht das Testobjekt.
Allgemeine Hinweise zur Stroboskop-Benutzung
Die nebenstehenden Bilder zeigen Ihnen, wie Sie das Stroboskop richtig einsetzen, um korrekte Werte bzw. ein optimales Standbild zu erzeugen oder welche Ursache, hinter z.B. einer doppelten (statt 110/ min sind es 220/ min) Drehzahl steckt. Die richtige Vorgehensweise gilt natürlich generell, auch wenn hier nur das Beispiel eines Antriebes und einer Antriebswelle behandelt werden.
Bei der Begutachtung nur eines Riementriebes ist ein optischer Stillstand leicht zu erreichen (irgend eine markante Stelle ist hier immer zu finden, auf die Sie das Stroboskop einstellen können).
Bei der Betrachtung von mehreren Keilriemen mit dem Stroboskop, sollten Sie, wenn möglich, z.B. bei Reparatur- o. Wartungsstillstand der Maschine eine Referenzlinie mittels Kreide senkrecht zur Laufrichtung über alle Riemen hinweg markieren.
Beispiel der Messung an einer Welle:
Bei einer gut bzw. optimal zentrierten Welle mit Laufrad messen Sie bei optischem Stillstand immer die tatsächliche Drehzahl. Hat das Laufrad aber einen axialen Schlag oder eine Unwucht, so werden Sie mit dem Stroboskop z.B. die doppelte Drehzahl messen. Diese Tatsache führt im Betrieb vor Ort sehr oft zu Fehleinschätzungen.
Technische Daten
Stroboskop - Modell PCE-OM 100A PCE-OM 200
Messbereiche 120 ... 6000 U/min
2 ... 100 Hz 30 ... 14000 U/min
0,5 ... 233,33 Hz
Auflösung 0,1 /min
Genauigkeit ±0,1 % ±0,01 %
Messabstand maximal (je nach Umgebung) 1 m 1,5 m
Blitzleistung 13 W
Signaleingang / Triggereingang 2,5 ... 15 V / NPN Open Collector / 2-Draht Näherungsschalter / Schaltrelais
Phasenverschiebung nein ja. bis 360 °
Lampe 13 W Xenonlampe, weiss, 6300 K
Versorgung wiederaufkadbarer Akku 14,4 V DC
Batterieladegerät 230 VAC / 50 ... 60 Hz / 1 m Kabel
Betriebszeit 60 min Dauerbetrieb / Ladezeit 15 h
Display 5-stelliges LED
Gehäuse ABS-Kunststoff
Abmessungen 178 x 121 x 219 mm 110 x 185 x 300 mm
Umgebungsbedingungen 0 ... +40 °C / <95 % r.F.
Gewicht 910 g 1880 g
Lieferumfang
1 x akku-betriebenes Stroboskop (entweder Modell PCE-OM 100A oder Modell PCE-OM 200), 1 x wieder aufladbarer Akku, 1 x Ladegerät, 1 x Stromkabel für das Ladegerät, Anleitung
Bei PCE-OM 200 zusätzlich mit Ersatzblitzröhre und Tragekoffer.
additional
Triggerkabel (Impulseingang)
Zum externen Anschluß ans Stroboskop, z.B. bei Triggerung via Maschinengeschwindigkeit.
Dieses Kabel dient der Impuls-Triggerung.
Triggerkabel (Kontakt-Eingang)
Zum externen Anschluss an das Stroboskop, z.B. bei Triggerung über eine externe Vorgabe der Geschwindigkeit. Dieses Kabel dient der Kontakt-Triggerung.
Ersatz-Akku
Wenn Sie das Stroboskop sehr oft und für einen längeren Zeitraum benutzen, empfiehlt es sich, einen Ersatz-Akku als Wechsel-Akku zu ordern. So haben Sie immer einen im Gerät und einen Akku am Ladenetzteil.
Ersatz-Xenonlampe
Die Langlebigkeit der Xenon-Blitzlampen ist sehr groß. Wenn Sie aber das Stroboskop etwa im Außendienst verwenden möchten und im Auftrag von Kunden Messungen durchführen, so sollten Sie immer eine Ersatz-Lampe dabei haben, um nicht plötzlich in Probleme zu kommen.
Stativ
Für etwaige Langzeitaufnahmen (z.B. 8 h) an Maschinen oder Anlagen empfiehlt es sich, das Stroboskop auf einem Stativ zu montieren. Dies kann sinnvoll sein bei einer Steuerung des Gerätes mittels externem Trigger bei Regelung der Blitzfrequenz anhand der Geschwindigkeit einer Maschine.
,,,alıntı,,,
Kalıcı Bağlantı
Yorum (1)
Yorum yaz!
28/12/2008 · Kategori: teknoloji
CDM Electronics is a certified small business, CCR# 42827, founded in 1993, CDM Electronics' mission is to provide our customers with exceptional interconnect products and value added services that meet or exceed our customers' expectations. We welcome the chance to design a creative solution to the most challenging issues.
Our Products
CDM Electronics is a NEDA Authorized Supplier for electronic connectors, coaxial cables and other interconnect products. This assures you that you are receiving factory new and approved products. With today's ever changing business climate, particularly in light of RoHS initiatives which transpired in July 2006, it is imperative that your applications perform to specification and in compliance with environmental and other government regulations. For those applications not requiring RoHS compliance, there are still several performance and reliability factors that are compromised when superior products are not deployed. Choose CDM for all of your interconnect sourcing requirements and you are guaranteed excellent products with on time deliveries.
Our Services
In 1999, CDM management recognized that customers wanted access to thousands of parts in stock ready for same day shipment. But this only represented half of our customers' needs. So
we embarked upon a program to expand our offering into the arena of cable assembly and value added programs. Since that time, CDM has experienced explosive growth and now provides a host of value added services, from "womb to tomb". We provide quick turn engineering and cable assembly services for prime contractors, as well as 2nd and 3rd tier providers. Our satisfied customer list includes Northrop Grumman, BAE, General Dynamics, and all branches of the United States military: Army, Navy, Air Force and Marines.
CDM credits our great staff, especially our brilliant engineering team, with our enormous success in this area.
Proactive Cost Reduction Program™
Process improvement and cost-saving solutions are as important to us as they are to you. Our "Proactive Cost Reduction Program" is a trademarked initiative created by CDM Electronics to constantly create cost-saving solutions for our customers.
Our People
From Reception to Shipping, CDM Electronics is proud to have the most loyal & dedicated employees. But it takes more than just our own employees to make our company great. We rely heavily on the expertise of several of our providers, especially our web designers:
Kalıcı Bağlantı
Yorum (yok)
Yorum yaz!
27/12/2008 · Kategori: teknoloji
Benefit from Huntron's 30 years of providing quality Diagnostic Tools for PCA Recovery
With today's val
id concerns for protection of our environment, the recovery, repair and recycling of printed circuit assemblies (PCAs) is a positive move towards sustainable environmental-friendly practices.
Huntron has been helping businesses troubleshoot and repair printed circuit assemblies for over 30 years. Repairing rather than discarding failed PCAs keeps the potentially harmful chemical components such as lead out of our world's landfills and disposal sites.
Below is a list of Huntron products to help you recover, repair and recycle PCAs:
• Huntron Tracker 2800
• Huntron Tracker Model 30
• Huntron TrackerPXI
• NFSA RF Prober
New Version of Huntron Workstation Available!
A new version of Huntron Workstation is now available for download. Go to the Workstation Support web page to download version 4.1.3273! Update December 22, 2008.
New Automated Near Field Signature Analysis
Combining the Huntron Access Robotic Probing Station, Huntron Workstation Software and the new Test Evolution (TEV) Non-Contact RF Near Field Probe with local synthetic measurement technology sets the standard for Near Field Signature Analysis (NFSA).
Placing the sensor, receiver and signal processing in one compact RF Probe assembly allows the sensing of EM fields emanating from RF circuitry. A specific position in a Near Field is defined as a Virtual Test Point™ (VTP) where a NFSA measurement is made. Identical circuits emanate nearly identical fields at the VTP. The combination of Huntron Prober and TEV RF Probe allows accurate positioning and measurement of VTPs. This provides the repeatability to measure VTP's from 200MHZ to 3GHZ on RF assemblies.
When used for test, an engineer examines the UUT schematic with an eye toward following the RF signal path. Using Huntron Workstation Software, points along that path are selected for Virtual Test Points (VTP). A set of known good boards are then scanned making and saving Near Field signatures at the VTP's. Unknown UUT's are scanned with the same VTP's against the saved signatures. Any deviation against stored signatures indicates areas of concern.
Near Field Signature Analysis (NFSA) is close proximity sensing of EM fields emanating from RF circuitry. Near Fields are close to active circuits with the strength dependent on power and circuit design. AC circuits radiate a unique frequency and magnitude “signature” being a function of frequency of operation, magnitude, distance to the test probe and geometric location of the probe.
The RF NFSA Prober will be available from Huntron to USA customers only in early 2009. Contact Huntron for more details on Near Field Signature Analysis.
Download the latest NFSA RF Prober brochure now!
Huntron Access USB Probers
The NEW Huntron Access USB Probers are the latest versions of the popular robotic probers used to automate testing of complex printed circuit boards. The Access USB Probers come in two sizes - the Access USB Prober can handle PCBs up to 19.4” by 14” and the larger Access 2 USB Prober can hold PCBs up to 22” by 23” in size. The new Probers come with a USB Probe Tip camera to monitor the probe placement as the test progresses. Both Probers uses linear encoders for incredible 20 micron accuracy. The new Access USB Probers can also be ordered with the Tracker Model 30 embedded inside the chassis for a space saving, all-in-one platform.
Download the latest Diagnostic Systems brochure now!
Huntron's flexible, automated diagnostic solutions help people solve circuit card problems.
Huntron was founded in 1976 with the introduction of the Huntron Tracker®, the pioneering troubleshooting tool that uses power-off signature analysis to identify component failures on printed circuit boards. Today, Huntron's reputation in providing automated power-off diagnostics results in instrumentation and software for test, inspection and repair of electronic printed circuit assemblies.
As density and complexity increase, printed circuit assemblies become tougher to probe and test. Huntrom complements conventional test equipment with access and test tools that catch the elusive problems other test methods often miss. The keys are physical and virtual access, which translates into meaningful results such as shorther design cycles, improved production yield and lower warranty costs. When you need to test, diagnose or troubleshoot complex circuit boards, Huntron lets you access, explore and discover more.
Contact us for more information on how we can help solve your test and troubleshooting needs
,,,alıntı,,, |
|
Kalıcı Bağlantı
Yorum (yok)
Yorum yaz!
26/12/2008 · Kategori: teknoloji
In times of rising energy prices and environmental regulations, optimization of energy flow is a most crucial issue. From heat delivery between central heating plants to end users or heat transfer flows in industrial processes: controlling and balancing the flow of energy is of utmost importance for cost conscious users.
FLUXUS BTU allows the easy determination of the energy flow in a system.
With temperature measurements made at the inlet and at the outlet of a system as well as flow measurement at the outlet , FLUXUS calculates the energy flow within that system. All this is done with temperature and flow measurement devices mounted on the outside of a pipe.
FLUXUS will display the actual energy flow through the system, and if needed, totalize the heat flow in order to obtain the energy quantity.
The values can easily be transmitted to a PC for display and analysis. The data obtained can be used for energy flow balancing or it can be transmitted to a process control system.
Kalıcı Bağlantı
Yorum (yok)
Yorum yaz!
« Önceki ::
